T-CHLOR
Sodium Hypochlorite 11.9% UN 1791ACTIVE
INGREDIENT: Sodium Hypochlorite
……….11.9% INERT
INGREDIENTS:……………………………87.5% TOTAL…………………………………………….100% KEEP OUT OF REACH OF CHILDREN DANGER
STATEMENT
OF PRACTICAL TREATMENT (FIRST AID) IF CONTACT WITH EYES OCCURS, flush with water for at
least 15 minutes, get prompt medical attention. IF CONTACT WITH SKIN OCCURS, wash with plenty of soap
and water. IF
SWALLOWED, drink large quantities of water.
DO NOT Induce vomiting. Call a Physician or Poison Control Center
immediately. HAZARDS
TO HUMANS AND DOMESTIC ANIMALS
DANGER:
Corrosive. May cause severe skin and eye irritation or chemical burns to
broken skin. Causes eye damage. Wear safety glasses or goggles and rubber
gloves when handling this product. Wash after handling. Avoid breathing
vapors. Vacate poorly ventilated areas as soon as possible. Do not return
until strong odors have dissipated. ENVIRONMENTAL
HAZARDS
This product is toxic to fish and aquatic organisms. Do not discharge effluent containing this product into lakes, streams, ponds estuaries, oceans or public waters unless this product is specifically identified and addressed in an NPDES permit. Do not discharge effluent containing this product into sewer systems without previously notifying the sewage treatment plant authority. For guidance, contact your State Water Board or Regional Office of the U.S. Environmental Protection Agency PHYSICAL
OR CHEMICAL HAZARDS
STRONG
OXIDIZING AGENT: Mix only with water according to label directions. Mixing
this product with chemicals (e.g. ammonia, acids, detergents, etc.) or
organic matter (e.g. urine, feces, etc.) will release chlorine gas which is
irritating to eyes, lungs and mucous membranes. IMPORTANT!
ALL SANITIZING APPLICATIONS
FOR
ALL FOOD CONTACT SURFACES AND OBJECTS-Remove food particles by flushing,
scraping and, when necessary, soaking. Wash thoroughly with a good deter9ent
or compatible cleaner and rinse with potable water before application of T-CHLOR
solution. Wet all surfaces thoroughly with T-CHLOR solution by immersion
flooding or spraying. Contact time must be at least two minutes. Drain
solution and air dry. Do not wash with potable water after sanitizing. T-CHLOR
solutions must not be re-used for sanitizing purposes. Prepare a fresh
solution daily if the old solution becomes diluted or soiled. STORAGE
AND DISPOSAL: Store
in a cool, dry area away from direct sunlight. In case of spill, flood area
with large quantities of water. Triple rinse empty container. Then offer for
recycling or reconditioning, or puncture and dispose of in a sanitary
landfill, or incineration or, if allowed by state and local authorities, by
burning. If burned, stay out of smoke. Product or rinsate that cannot be
used should be diluted with water and disposed of in a sanitary sewer. Do
not contaminate food or feed by storage, disposal or cleaning of equipment. SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, CONCERNING THIS MATERIAL OR THE USE OF THIS PRODUCT OTHER THAN INDICATED ON THIS LABEL. BUYER ASSUMES ALL RISK OF USE AND/OR HANDLING OF THIS MATERIAL WHEN SUCH USE AND/OR HANDLING IS CONTRARY TO LABEL INSTRUCTIONS.
|
|
DIRECTIONS
FOR USE -
It
is a violation of federal law to use this product in a manner inconsistent
with its labeling. NOTE: This product degrades with age. Use a chlorine
test kit and increase dosage, as necessary, to obtain the required level of
available chlorine. SANITATION
OF NON-POROUS FOOD CONTACT SURFACES RINSE
METHOD-A
solution of 100 ppm available chlorine may be used in the sanitizing
solution if a chlorine test kit is available. Solutions containing an
initial concentration of 100 ppm available chlorine must be tested and
adjusted periodically to insure that the available chlorine does not drop
below 50 ppm. Prepare a 100 ppm sanitizing solution by thoroughly mixing 1
oz. of this product with 10 gallons of water. if no test kit is available,
prepare a sanitizing solution by thoroughly mixing 2 oz. of this product
with 10 gallons of water to provide approximately 200 ppm available
chlorine by weight. Clean equipment surfaces in the normal manner. Prior to
use, rinse all surfaces thoroughly with the sanitizing solution, maintaining
contact with the sanitizer for at least 2 minutes. If solution contains
less than 50 ppm available chlorine, as determined by a suitable test kit,
either discard the solution or add sufficient product to re-establish a 200
ppm residual. Do not rinse equipment with water after treatment and do not
soak equipment overnight. Sanitizers used in automated systems may be used
for general cleaning but may not be re-used for sanitizing purposes. IMMERSION
METHOD-A solution of 100 ppm available chlorine may be used in the
sanitizing solution if a chlorine test kit is available. Solutions
containing an initial concentration of 100 ppm available chlorine must be
tested and adjusted periodically to insure that the available chlorine
does not drop below 50 ppm. Prepare a 100 ppm sanitizing solution by
thoroughly mixing 1 oz. of this product with 10 gallons of water. If no
test kit is available, prepare a sanitizing solution by thoroughly mixing 2
oz. of this product with 10 gallons of water to provide approximately 200
ppm available chlorine by weight. Clean equipment in the normal manner.
Prior to use, immerse equipment in the sanitizing solution for at least 2
minutes and allow the sanitizer to drain. If solution contains less than 50
ppm available chlorine as determined by a suitable test kit, either discard
the solution or add sufficient product to re-establish a 200 ppm residual.
Do not rinse equipment with water after treatment. Sanitizers
used in automated systems may be used for general cleaning but may not be
re-used for sanitizing purposes. FLOW/PRESSURE METHOD-Disassemble
equipment and thoroughly clean after use. Assembly equipment in operating
position prior to use. Prepare a volume of a 200 ppm available chlorine
sanitizing solution equal to 110% of volume capacity of the equipment by
mixing the product in a ratio of 2 oz. product with 10 gallons of water.
Pump solution through the system until full flow is obtained at all
extremities, the system is completely filled with the sanitizer and all air
is removed from the system. Close drain valves and hold under pressure for
at least 2 minutes to insure contact with all internal surfaces. Remove
some cleaning solution from drain valve and test with a chlorine test kit.
Repeat entire cleaning/sanitizing process if effluent contains less than 50
ppm available chlorine. CLEAN-IN-PLACE METHOD-Thoroughly clean equipment after use. Prepare a volume of a 200 ppm available chlorine sanitizing solution equal to 110% of volume capacity of the equipment by mixing the product in a ratio of 2 oz. product with 10 gallons of water. Pump solution through the system until full flow is obtained at all extremities, the system is completely filled with the sanitizer and all air is removed from the system. Close drain valves and hold under pressure for at least 10 minutes to insure contact with all internal surfaces. Remove some cleaning solution from the drain valve and test with a chlorine test. Repeat entire cleaning/sanitizing process if effluent contains less than 50 ppm available chlorine. SPRAY/FOG METHOD-Pre-clean all surfaces after use. Use a 200 ppm available chlorine solution to control bacteria, mold or fungi and a 600 ppm solution to control bacteriophage. Prepare a 200 ppm sanitizing solution of sufficient size by thoroughly mixing the product in a ratio of 2 oz. product with 10 gallons of water. Prepare a 600 ppm solution by thoroughly mixing the product in a ratio of 6 oz. product with 10 gallons of water. Use spray or fogging equipment which can resist hypochlorite solutions. Always empty and rinse spray/fog equipment with potable water after use. Thoroughly spray or fog all surfaces until wet, allowing excess sanitizer to drain. Vacate area for at least 2 hours. Prior to using equipment, rinse all surfaces treated with a 600 ppm solution with a 200 ppm solution. OTHER USES: This product has several additional approved uses. DOT
shipping name: Hypochlorite Solution 11.9%, Corrosive Material, UN 1791 DOT
E-6614 Emergency
# For Chemtrec: 1-800-424-9300
DANGER: THIS CONTAINER HAZARDOUS WHEN EMPTIED.
Since emptied container retains product residues (vapor or liquid),
all labeled hazard precautions must be observed. Price Per gallon In: 1 gallon bottles $3.50 Call Lyn Distributing for Large Orders
1-800-366-5022 Purchase On-line Here |
